GET 15% OFF
We will be out of office 12/23 - 1/1. Happy Holidays!
Limited Edition: eeBrakes Magnum
New: Second Generation Kitsuma
NEW: GXC Stem
Previous slide
Next slide
Cane Creek Logo
Cane Creek Logo
Cane Creek Logo

eeSilk Stem Axle and Bushing Service Procedure

Required Tools

Recommendations and Warnings

 
  • Cane Creek recommends replacing all of the bushing during this service so the pivots wear evenly. 
  • During Disassembly – Pivot axles must be removed by being pressed out towards the drive-side of the bicycle. 
  • During Reassembly – Pivot axles must be installed by being pressed in towards the non-drive side of the bicycle. 

Part Numbers

 
  • BAJ0081 – Compliance switch service kit with bushings
  • BAJ0082 – Preload wedge
  • BAJ0083 – Faceplate with bolt
  • BAJ0091 – Service Tool

Steps:

Remove the Elastomer

Step 1

  • Remove the eeSilk Stem from the bicycle.

  • Next remove the elastomer by using a 4mm hex wrench – loosen elastomer bolt on top of stem body.

  • With the preload assembly removed, lift the stem and remove the elastomer.

Identify drive side and non-drive side of tool

Step 2

  • Drive side of the tool has larger hole and accepts 8mm nut
  • Non-drive side of the tool has smaller hole and accepts 4mm allen bolt

The axle can only be pressed out towards the drive side

  •  

Position tool in place over stem

Step 3

  • Verify drive side & non-drive side of the stem

  • Removing one side of the tool will help while positioning tool into place  

  • Once positioned properly equally tighten tool

    DO NOT OVER TIGHTEN

Press and Remove Stem Axle

Step 4

  • Pin tool will fit perfectly into non-drive side hole (Use pin side of pin tool to press against stem axle)

  • Position stem in vice

  • Tighten vice evenly – driving pin tool into non-drive side of stem

  • Axle will be press out toward drive side

Remove and install bushings

Step 5

  • Separate stem pivot exposing the bushings

  • Using a flat tool (razor / screwdriver) carefully remove bushings

  • Install new bushings and washers by press in by hand

Servicing the Compliance Switch

Step 6

  • Use T10 torque wrench to remove compliance switch

  • Remove the O-Ring

  • Next use a pick tool to remove the C-Clip

  • Remove the Helix Assembly

    • Turn to Firm mode (clockwise)

    • The Wedge will disconnect from Helix Assembly (careful not to loose the dowel pin in the wedge)

 

Reassembly of Compliance Switch

Step 7

  • Install Wedge back into position (with dowel pin)

  • Install the Helix assembly onto wedge

    • Correct orientation of helix is critical

    • First orientate rounded end of Helix towards drive side then twist Helix into position (Rounded end will face non-drive side when properly seated)

  • Reinstall c-clip
  • Reinstall o-ring
  • Reinstall Compliance Switch 
  • Tighten T10 
 

Pressing axle back into position

Step 8

  • Place stem body back into position between pivots

  • Install axle from drive side -by hand

  • Position tool over stem (same as Step 3)

  • Position pin tool on drive side (pin side of pin tool towards the axle)

  • Place stem and tool into vice

  • Press axle into stem by tightening vice

When line on pin tool is lined up with tool the axle is fully seated

Reinstall elastomer

Step 9

  • Elastomer can only be install in one orientation. Make sure chosen elastomer rating indication is facing down. Elastomer is marked with “TOP” and should face up toward stem .Curved surfaces should be facing the front of the bike

  • While pressing down slightly on the top of the stem, install preload wedge assembly with 4mm hex wrench.  Applying downward force to the stem will aid in proper elastomer wedge bolt alignment, failure to do so may result in permanent damage.

Reinstall eeSilk stem on bike and go ride!

Free US shipping on all orders $99+
828-641-9560
355 Cane Creek Rd
Fletcher, NC 28732

Warehouse Deals

Customer Support

Cane Creek Policies

Employment

B2B Website Access

Warranty Information

Bicycle Friendly Business

GET 15% OFF

Sign Up For a 15% Off Coupon Code* + Exclusive Promotions, Product Announcements & More
Subscribe

HOURS

Monday: 10:00 am – 5:00 pm
Tuesday – Thursday: 10:00 am – 5:00 pm
Friday: 10:00 am – 5:00 pm
Saturday – Sunday: Closed

LET'S CONNECT

Browse Community Content

  • Klarna Payment Badge
We ship to: United States & Canada.
*15% off coupon code for email sign up does not include sale or warehouse deals items.
© 2024 Cane Creek Cycling Components
Asheville Website Design | BECK